TFSI Audi A6 knock sensor replacement

Audi A6 A7 Ignition system

Tfsi Firing order: 1-5-4-8-6-3-7-2

Removing and installing knock sensors :

⇒ Removing and installing knock sensor – G61- (cylinder bank 1, right-side) – A6 only 

Removing and installing knock sensor G61 (cylinder bank 1, right-side) – A7 only

⇒ Removing and installing knock sensor 2 G66 (cylinder bank 1, right-side)
⇒ Removing and installing knock sensor 3 G198 (cylinder bank 2, left-side)
⇒ Removing and installing knock sensor 4 G199 (cylinder bank 2, left-side)

Removing and installing knock sensor – G61- (cylinder bank 1, right-side) – A6 only 

TFSI Audi a6 knock sensor replacement
TFSI Audi a6 knock sensor replacement

– Disconnect earth wire at battery with ignition switched off.
– Remove bolts -arrows- and detach air duct -2-.
– Release catches -arrows A- and detach air duct -1- on left and
right -arrow B-.

– Release retaining pins for radiator on both sides and pull out
upwards -arrows-.
– Push radiator towards the front.
– Remove tensioner for poly V-belt ⇒ Rep. gr. 13 .

– Unplug electrical connector -3-.
– Remove nut -1- and detach B+ wire -2-.

– Unscrew bolts -arrows- for alternator approx. 6 turns.
– Tap carefully on bolt heads with a hammer to release sliding
bushes of alternator mountings.
– Remove bolts completely.
– If fitted, remove silencer for auxiliary heater ⇒ Rep. gr. 82 .
– Move alternator as far as possible to the right.
– Loosen bolts and detach coolant hoses -2 and 4- with con‐
nections.

tfsi ignition system,tfsi engine problems,tfsi engine cover,tfsi firing order,3.0 tfsi firing order,tfsi audi,tfsi audi a6,40 tfsi audi a6,tfsi audi a7,2.0 tfsi knock sensor location,2.0 tfsi knock sensor

– Unplug electrical connector -1-.
– Unscrew bolt -2- and remove knock sensor 1 -G61- .
Installing
Installation is carried out in the reverse order.

tfsi ignition system,tfsi engine problems,tfsi engine cover,tfsi firing order,3.0 tfsi firing order,tfsi audi,tfsi audi a6,40 tfsi audi a6,tfsi audi a7,2.0 tfsi knock sensor location,2.0 tfsi knock sensor

Removing and installing knock sensor G61 (cylinder bank 1, right-side) – A7 only

tfsi ignition system,tfsi engine problems,tfsi engine cover,tfsi firing order,3.0 tfsi firing order,tfsi audi,tfsi audi a6,40 tfsi audi a6,tfsi audi a7,2.0 tfsi knock sensor location,2.0 tfsi knock sensor

Removing
– Disconnect earth wire at battery with ignition switched off.
– Remove alternator

– Unplug electrical connector -1-.
– Unscrew bolt -2- and remove knock sensor 1 -G61- .
Installing
Installation is carried out in the reverse order.

Removing and installing knock sensor 2 G66 (cylinder bank 1, right-side)

TFSI Audi a6 knock sensor

Removing
– Remove front wheel (right-side) ⇒ Wheels and tyres
– Remove cover -1- for drive shaft in wheel housing (right-side).
– Remove engine mounting (right-side)

– Remove nut -2- and move earth wire clear.
– Remove bolts -arrows- and detach engine support -1- (rightside).
– Unplug electrical connector -4- from starter (push retainer to
rear and press down release catch).
– Unfasten nut -3- and detach battery positive wire from solenoid switch.

– Unplug electrical connector -1-.
– Unscrew bolt -2- and remove knock sensor 2 -G66- .
Installing
Installation is carried out in the reverse order.

Removing and installing knock sensor 3 G198 (cylinder bank 2, left-side)

Tfsi ignition system

Removing
– Remove air conditioner compressor ⇒ Air conditioning system
– Detach electrical connector -2- from bracket and unplug.
– Unscrew bolt -1- and remove knock sensor 3 -G198- .

 Installing
Installation is carried out in the reverse order


Removing and installing knock sensor 4 G199 (cylinder bank 2, left-side)

Tfsi ignition system

Removing
– Remove electromechanical steering rack ⇒ Running gear,
front-wheel drive and four-wheel drive;
– Unplug electrical connector -arrow-.

– Remove bolt -2-.
– Detach knock sensor 4 -G199- and unplug electrical connector -1-.
Installing
Installation is carried out in the reverse order.


HOME

1 Comment

admin · February 4, 2023 at 7:39 am

If you require any further information let me know.

Leave a Reply

Avatar placeholder

Your email address will not be published. Required fields are marked *